1. Maintenance and maintenance of digital display biochemical incubator: 1. Observe daily whether the temperature of the incubator meets the regulations. If an abnormal situation is found, please ask a professional to repair it in time. 2. When the lighting in the box is abnormal, the lighting fixture should be replaced in time. 3. When the heating (cooling) is abnormal, check whether the heating furnace wire is damaged and repair it in time. 4. Clean the outside of the incubator in time to keep it clean and dust-free. Use sterile water to clean the liner of the incubator thoroughly once a week. Replace different types of disinfection water every quarter to avoid the emergence of drug-resistant strains. 5. The performance of this equipment should be verified once a year. 2. Maintenance and maintenance of digital display light incubator: 1. The shell of the incubator should be reliably grounded. 2. The incubator should be placed in a cool, dry, well-ventilated place away from heat sources and sunlight. Place it steadily to prevent vibration and noise. 3. In order to ensure the effective heat dissipation of the condenser, the distance between the condenser and the wall should be greater than 100mm, the side of the box should have a gap of 50mm, and the top of the box should have at least 300mm of space. 4. During transportation, repair and maintenance of the incubator, avoid collision, shaking and vibration, and the maximum inclination is less than 45 degrees. 5. The instrument suddenly does not work, please check whether the fuse tube is burnt out, and check the power supply. 6. When cooling the incubator, it is not appropriate to make the difference between the temperature in the chamber and the ambient temperature greater than 25 degrees. 3. Maintenance of the shaking incubator: 1. During the continuous working period of the instrument, periodic inspection should be done every three months; check the fuses, control components and fastening screws, and whether there are water drops, dirt, etc. falling on the motor and control components. 2. The bearings of the transmission part have been filled with a proper amount of grease before leaving the factory. During the continuous operation of the instrument, the grease should be refilled every six months, and the filling amount accounts for about 1/3 of the bearing space. 3. The compressor should avoid continuous starting. 1. Observe daily whether the temperature of the incubator meets the regulations. If an abnormal situation is found, please ask a professional to repair it in time. 2. When the lighting in the box is abnormal, the lighting fixture should be replaced in time. 3. When the heating (cooling) is abnormal, check whether the heating furnace wire is damaged and repair it in time. 4. Clean the outside of the incubator in time to keep it clean and dust-free. Use sterile water to clean the liner of the incubator thoroughly once a week. Replace different types of disinfection water every quarter to avoid the emergence of drug-resistant strains. 5. The performance of this equipment should be verified once a year. 2. Maintenance and maintenance of digital display light incubator: 1. The shell of the incubator should be reliably grounded. 2. The incubator should be placed in a cool, dry, well-ventilated place away from heat sources and sunlight. Place it steadily to prevent vibration and noise. 3. In order to ensure the effective heat dissipation of the condenser, the distance between the condenser and the wall should be greater than 100mm, the side of the box should have a gap of 50mm, and the top of the box should have at least 300mm. 4. During transportation, repair and maintenance of the incubator, avoid collision, shaking and vibration, and the maximum inclination is less than 45 degrees. 5. The instrument suddenly does not work, please check whether the fuse tube is burnt out, and check the power supply. 6. When cooling the incubator, it is not appropriate to make the difference between the temperature in the chamber and the ambient temperature greater than 25 degrees. 3. Maintenance of the shaking incubator: 1. During the continuous working period of the instrument, periodic inspection should be done every three months; check the fuses, control components and fastening screws, and whether there are water drops, dirt, etc. falling on the motor and control components. 2. The bearings of the transmission part have been filled with a proper amount of grease before leaving the factory. During the continuous operation of the instrument, the grease should be refilled every six months, and the filling amount accounts for about 1/3 of the bearing space. 3. The compressor should avoid continuous starting. From: http: // BLACKPINK cheer,BLACKPINK Light stick,BLACKPINK souvenir Shanghai Liuyuan Trading Co. , Ltd. , https://www.ly-weighing.com